Custom Tension Springs by BQUQ | Precision Manufacturing Made in China
What This Tension Spring Does and Why Tolerance Matters This is a custom Tension Spring built for exact force control in mechanical assemblies. You get a load accuracy of ±3% across the full deflectio
Get a Fast Quote for This Part
Send us your drawing / quantity / material — reply within 24h.
What This Tension Spring Does and Why Tolerance Matters
This is a custom Tension Spring built for exact force control in mechanical assemblies. You get a load accuracy of ±3% across the full deflection range, with an outer diameter tolerance of ±0.02 mm and a free length tolerance of ±0.05 mm. We hold wire diameter to ±0.01 mm, which directly stabilizes your spring rate. Lead time is 7 days for prototypes and 15 days for production runs, and we ship from our Dongguan factory with a hardness range of 45–52 HRC after heat treatment. No MOQ—order one piece or one million.
Wire Materials We Stock for Tension Spring Load Curves
We keep 12 wire grades in-house so your Tension Spring doesn't wait on raw material. For general use, we use music wire ASTM A228 (0.2–6.0 mm diameter) and hard-drawn steel A227. For corrosive or high-temp environments, we offer stainless steel 302 (A313) and 316 (A478). For high-fatigue applications like valve return mechanisms, we use chrome silicon A401 and chrome vanadium A231. Each coil is wound on a CNC former with a pitch accuracy of ±0.03 mm, which keeps your load curve linear within 1% of calculated values.
Heat Treatment and Surface Finish That Prevent Early Breakage
We stress-relieve every Tension Spring at 250–300°C for 30 minutes after coiling. This removes residual stress from the wire drawing process and raises the elastic limit by 15%. For high-cycle applications, we add shot peening (intensity 0.2–0.4 mmA) to compress the surface layer, increasing fatigue life by 200% compared to unpeened springs. Standard surface finish is Ra 0.8 µm, but we can achieve Ra 0.4 µm with a micro-polish pass. If your spring needs corrosion resistance, we apply zinc plating (8–12 µm) or electroless nickel (25 µm) per ASTM B633.
End Configurations: How We Hook Your Spring Into the Assembly
Your Tension Spring fails first at the hooks, so we machine them with the same precision as the coils. We offer six hook styles: full loop, half loop, extended hook, cross-over center loop, double torsion, and reduced OD hook. Each hook is formed on a dedicated mandrel to hold the inside diameter to ±0.03 mm. We inspect hook alignment with a vision system that checks angular deviation to ±1.5 degrees. For dynamic loads, we add a stress-relief notch at the hook bend to eliminate crack initiation points—this is standard, not an extra-cost option.
Inspection Before Every Shipment: Force Testing on 100% of Coils
Every Tension Spring we ship passes a load test at 25%, 50%, and 75% of maximum deflection. We use a digital force gauge with an accuracy of ±0.5% of reading, and we record the actual load curve on a certificate of conformance. Free length and outer diameter are checked on a CNC optical comparator with a resolution of 0.001 mm. We also perform a 10-cycle compression set test on each batch to confirm the spring returns to within 0.2% of its original free length. If any unit fails, the entire batch is stopped and re-sorted.
Packaging and Anti-Corrosion Protection for Ocean Freight
We pack Tension Springs in anti-static VCI (vapor corrosion inhibitor) bags, then place them in double-wall cartons with dividers to prevent interlocking. For springs over 50 mm free length, we use individual tubes to avoid tangling. Each carton is labeled with your part number, lot number, and heat treatment batch. We have shipped to 34 countries without a single corrosion complaint since 2018. For express shipments, we use vacuum-sealed bags with desiccant packs rated for 60 days of humidity protection.
Lead Time and MOQ: Real Numbers for Your Production Schedule
Prototype Tension Springs (1–50 pieces) ship in 7 days from drawing approval. Production runs (50–10,000 pieces) ship in 15 days. For orders above 10,000 pieces, add 5 days for wire spool changes and additional QC sampling. MOQ is zero—we accept a single prototype spring. Tooling cost is $0 for standard wire diameters (0.2–6.0 mm). For non-standard wire, we charge a $150 setup fee, which is waived for orders above 2,000 pieces. We provide free DFM feedback within 24 hours of receiving your drawing, including spring rate calculations and hook stress analysis.
Parameter
Specification
Wire diameter range
0.2 mm – 6.0 mm
Materials
ASTM A228, A227, A313, A478, A401, A231
Free length tolerance
±0.05 mm (up to 100 mm length)
Outer diameter tolerance
±0.02 mm
Hardness (after heat treatment)
45–52 HRC
Surface finish (Ra)
0.8 µm standard, 0.4 µm optional
Load accuracy
±3% at specified deflection
Hook angular deviation
±1.5 degrees
Fatigue life (shot peened)
10^6 cycles at 50% max load
Lead time (prototype / production)
7 days / 15 days
MOQ
No MOQ (1 piece accepted)
How Our Tension Spring Fits Into Your Broader CNC Machining Workflow
Your Tension Spring is often the last mechanical component to be specified, but it interacts directly with your machined parts. If your spring seat has a tight bore tolerance, check our CNC machining tolerances guide to confirm your hole tolerances align with our spring OD tolerance of ±0.02 mm. For springs that sit on a threaded stud or a turned shaft, the surface finish of your mating part affects friction and spring seating—our CNC cutting tool selection guide covers how to achieve Ra 0.4 µm on those surfaces. We also manufacture the mating components (CNC-machined spring seats, retaining washers, and stamped hooks) in the same factory, so you can order a complete sub-assembly with a single drawing—saving you a separate supplier audit.
What is the minimum order quantity for a custom Tension Spring?
We have no MOQ—you can order a single prototype spring to validate your design, and production pricing kicks in at 50 pieces.
Can you match an existing Tension Spring’s load curve exactly?
Yes, send us a sample and we will reverse-engineer the wire diameter, coil count, and free length using a force-displacement curve tracer, then replicate the load curve within ±2%.
How do you guarantee quality for high-volume Tension Spring orders?
We perform in-process SPC (statistical process control) on every 50-piece batch, checking OD, free length, and load at 3 points, and we provide a full inspection report with each shipment.
What is the fastest lead time for an urgent Tension Spring order?
For standard wire diameters in stock, we can ship a 100-piece prototype in 72 hours using express machining and overnight heat treatment, but this requires drawing approval by 10 AM CST.
Get a Firm Quote Within 12 Hours—Send Your Drawing Today
Send us your Tension Spring drawing, a sketch, or a sample part. Our engineers will respond within 12 hours with a firm quote, including wire material recommendation, load curve calculation, and a DFM note on hook geometry. We are a precision manufacturing factory in Dongguan, China, with 20 years of CNC machining, stamping, and spring-making experience. No MOQ, no tooling fee for standard wire, and we speak English—no translation delays. Email your drawing to sc@bquq.com or message us on WhatsApp at +86 13713157787. We will also run a free stress analysis for your hook design to prevent early failure. Send your drawing now and get a price that competes with local suppliers while holding ±0.02 mm tolerance.
Straight answers from the factory, not a sales brochure.
How do I get a quote for this part?
Send your drawing (STEP, IGES, DWG, DXF or PDF) with quantity and target material to sc@bquq.com or WhatsApp +86 137 1315 7787. Our engineers review the drawing and reply with price, lead time and tooling cost.
What is your MOQ?
We do not set a fixed MOQ. The minimum is decided per part and per process, so tell us your target quantity and we quote against it. Small trial batches are accepted for new parts.
What is the lead time?
Lead time is agreed per order, based on the date you need, the quantity, the material and whether tooling is required. Send your target date with the drawing and we confirm what is achievable before you commit.
What tolerance can you hold?
CNC machining holds ±0.005 mm. Stamping, spring and extrusion parts are made to the tolerances marked on your drawing, and we confirm achievable values at quotation so there are no surprises at inspection.
Can you manufacture parts to my drawing?
Yes. Every order is made to the customer drawing or sample. We run CNC machining, metal stamping, spring coiling and aluminium heat sink extrusion in-house in Dongguan, so one supplier covers the whole part.
STEP, IGES, DWG, DXF and PDF. A 2D drawing with tolerances and surface finish requirements is preferred alongside the 3D model. Hand sketches can be quoted after our engineers redraw them.
How is quality controlled?
Inspection runs through the process, not only at the end: first article approval, in-process checks and a final report per batch, measured with CMM and optical equipment. Material certificates are available on request.
Where is the factory and do you ship worldwide?
Our factory is in Dongguan, Guangdong, China, operating since 2005. We ship worldwide by express, air and sea, and work with the forwarder nominated by the buyer.