Custom Coil Springs Precision Manufacturing | BQUQ Made in China
What This Coil Spring Delivers in Hard Numbers This is a custom coil spring built from wire diameters 0.1 mm to 12 mm, with a pitch tolerance of ±0.01 mm and a free length tolerance of ±0.05 mm. You g
Get a Fast Quote for This Part
Send us your drawing / quantity / material — reply within 24h.
This is a custom coil spring built from wire diameters 0.1 mm to 12 mm, with a pitch tolerance of ±0.01 mm and a free length tolerance of ±0.05 mm. You get a spring that holds its load within ±3% across 10,000 cycles, surface finish at Ra 0.4 μm, and a hardness range of 45–52 HRC for fatigue resistance. From drawing approval to shipment, your coil spring leaves our Dongguan factory in 15 days, and we run no minimum order quantity (no MOQ) on any custom spring.
Why Your Compression Spring Fails Early — and How We Prevent It
Most coil springs fail from residual stress left after coiling, not from material defects. We stress-relieve every spring at 300–350°C for 30 minutes in a nitrogen atmosphere, which removes internal stress and boosts fatigue life by 40% compared to as-coiled springs. For springs under 2 mm wire diameter, we add a shot-peening step at 0.3 A intensity to close surface micro-cracks. Our load testing rig checks force at 25%, 50%, and 75% of total deflection on every batch, so you never get a spring that sags after 1,000 cycles.
Materials and Heat Treatment We Use for Coil Springs
We start with four wire grades: music wire (SWP-A) for general use, chrome silicon (SWOSC-V) for high-temperature up to 250°C, stainless steel 302 (SUS302) for corrosion resistance, and Inconel X-750 for exotic applications above 400°C. After coiling, we apply the right heat cycle — for chrome silicon, that means oil quenching at 850°C followed by tempering at 420°C to hit 48–52 HRC. Stainless springs get a 400°C precipitation hardening, not a standard temper, to prevent brittleness. Every heat lot gets a hardness test on a Rockwell tester, and we record the HRC value on the inspection sheet you receive with the springs.
Specification
Value
Wire diameter range
0.1 mm – 12 mm
Free length tolerance
±0.05 mm (under 50 mm), ±0.10 mm (above 50 mm)
Outer diameter tolerance
±0.02 mm for wire ≤ 2 mm; ±0.05 mm for wire > 2 mm
How We Control Coil Spring Runout and End Flatness
Runout — the wobble when a spring rotates — kills performance in valve and clutch applications. We hold total runout to 0.02 mm by grinding both end faces parallel to within 0.01 mm on a double-disc grinder. For closed-ground ends, we grind the last 1.5 coils flat to 90° ±1° relative to the spring axis. We check every 50th spring on an optical projector at 20× magnification, measuring the angle between the end face and the spring axis. If you need tighter runout than 0.02 mm, we can grind to 0.01 mm with a 3-day lead time extension.
Inspection Before Every Shipment: What You Receive
Every coil spring order ships with a full dimensional report, not a generic certificate. The report lists free length, outer diameter, wire diameter, pitch, total coils, load at three deflection points, and hardness HRC — all measured on actual parts from your batch. We use a CMM for OD and pitch, a digital load tester for force, and a Rockwell tester for hardness. For orders above 500 pieces, we inspect 10 pieces per 1,000 and include the raw data. Springs that fail any spec are scrapped, not reworked, because re-coiling changes grain structure.
Handling Tight Deadlines Without Cutting Corners
Standard coil spring lead time is 15 days from drawing approval to shipment. Need it faster? We keep SWP-A and SUS302 wire in stock in 12 diameters, so prototype springs can ship in 5 days. For production runs above 10,000 pieces, we run two shifts on our CNC coiling machines, which cuts lead time to 10 days without changing inspection steps. We quote exact dates, not ranges — if we say the 15th, the springs are on the truck on the 15th. For material selection and heat treatment details, check our CNC cutting tool selection guide to understand how spring wire interacts with tooling, and our CNC machining tolerances guide for how we hold ±0.01 mm on every dimension.
What is the minimum order quantity for custom coil springs?
There is no MOQ — we run single prototypes at the same tolerance and inspection level as million-piece orders, which is why engineers across Europe and North America trust our precision manufacturing from a Dongguan factory.
Can you match a spring spec from a broken sample or a drawing?
Yes — send us a physical sample or a drawing with wire diameter, free length, OD, total coils, and load requirements, and we will reverse-engineer the spring and send a free pre-production sample within 7 days.
How do you verify load tolerance and fatigue life?
We test load at 25%, 50%, and 75% deflection on a calibrated load tester, and for high-cycle applications, we run a 10,000-cycle fatigue test on 3 samples per batch and include the results in your inspection report.
What is the fastest lead time for a coil spring prototype?
Prototypes in SWP-A or SUS302 wire ship in 5 days from drawing approval, and production orders up to 50,000 pieces ship in 15 days — we never quote a longer lead time than we can hold.
Get a Firm Quote Within 12 Hours — Send Your Drawing
Email your coil spring drawing or a photo with dimensions to sc@bquq.com, or message us on WhatsApp at +86 13713157787. We reply with a firm price, exact lead time, and a DFM check within 12 hours — not a vague estimate. Our precision manufacturing, made in China, is backed by 20 years of CNC machining, stamping, and spring production for automotive, medical, and electronics clients. No MOQ, no minimum order value, no surprises. Send your drawing today and get a spring that passes inspection on the first try.
Straight answers from the factory, not a sales brochure.
How do I get a quote for this part?
Send your drawing (STEP, IGES, DWG, DXF or PDF) with quantity and target material to sc@bquq.com or WhatsApp +86 137 1315 7787. Our engineers review the drawing and reply with price, lead time and tooling cost.
What is your MOQ?
We do not set a fixed MOQ. The minimum is decided per part and per process, so tell us your target quantity and we quote against it. Small trial batches are accepted for new parts.
What is the lead time?
Lead time is agreed per order, based on the date you need, the quantity, the material and whether tooling is required. Send your target date with the drawing and we confirm what is achievable before you commit.
What tolerance can you hold?
CNC machining holds ±0.005 mm. Stamping, spring and extrusion parts are made to the tolerances marked on your drawing, and we confirm achievable values at quotation so there are no surprises at inspection.
Can you manufacture parts to my drawing?
Yes. Every order is made to the customer drawing or sample. We run CNC machining, metal stamping, spring coiling and aluminium heat sink extrusion in-house in Dongguan, so one supplier covers the whole part.
STEP, IGES, DWG, DXF and PDF. A 2D drawing with tolerances and surface finish requirements is preferred alongside the 3D model. Hand sketches can be quoted after our engineers redraw them.
How is quality controlled?
Inspection runs through the process, not only at the end: first article approval, in-process checks and a final report per batch, measured with CMM and optical equipment. Material certificates are available on request.
Where is the factory and do you ship worldwide?
Our factory is in Dongguan, Guangdong, China, operating since 2005. We ship worldwide by express, air and sea, and work with the forwarder nominated by the buyer.