Phosphor Bronze Corrugated Spring Washer Stamping | BQUQ Precision
Phosphor Bronze Corrugated Spring Washer Stamping from BQUQ gives you a load-bearing washer that stays elastic after 100,000 cycles. We hold flatness within 0.02 mm and thickness tolerance ±0.01 mm, w
Get a Fast Quote for This Part
Send us your drawing / quantity / material — reply within 24h.
Phosphor Bronze Corrugated Spring Washer Stamping from BQUQ gives you a load-bearing washer that stays elastic after 100,000 cycles. We hold flatness within 0.02 mm and thickness tolerance ±0.01 mm, with a standard lead time of 5 working days for prototypes. Hardness sits at 80–100 HRB, not HRC, because phosphor bronze needs spring temper, not brittle hardness.
Why Corrugation Beats Flat Washers Under Vibration
A flat washer only distributes load. A corrugated washer adds axial deflection — it pushes back against loosening bolts. Our stamping die forms three or five waves, giving you a spring rate of 15–40 N/mm depending on thickness. We control wave height within ±0.03 mm so your preload stays predictable. If you need a lock washer that survives high-frequency vibration on a motor mount or PCB standoff, this geometry works.
Phosphor Bronze C5191 vs C5210 — Which We Stock
We run both C5191 (tin 5–7%) and C5210 (tin 7–9%) in strip form. C5191 gives you higher fatigue strength for repeated compression; C5210 offers better corrosion resistance in salt spray. Both come in half-hard, hard, and extra-hard tempers. For most washer applications, we recommend extra-hard C5191 — it returns to shape after 10% deflection without cracking at the wave peaks.
Die Design That Prevents Cracking at Wave Peaks
Corrugated washers crack when the bend radius is too tight. Our dies use a minimum inside radius of 1.5× material thickness, never less. We also add a coining step at the wave crest — that compresses the grain structure and removes micro-tears from the initial bend. Result: no edge cracks in 99.7% of parts after 50,000 stamping hits. We check every die with a profilometer before production starts.
Surface Finish and Burr Control on Each Wave
Stamping leaves a burr on the shear edge. For a spring washer, burrs can cut into your mating surface. We limit burr height to 0.05 mm maximum, and our secondary vibratory finishing brings surface roughness to Ra 0.4 µm. If you need a mirror finish for electrical contact, we add a brush-polish step — that takes 2 extra days but removes all tooling marks.
Inspection Before Every Shipment — Not a Random Sample
We measure 100% of critical dimensions on a CMM for orders under 1,000 pieces. For larger runs, we use an automated optical inspector that checks wave height, outer diameter, and thickness on every 50th part. We also do a compression test on 5 pieces from each batch: we compress the washer to 70% of its free height and verify it springs back within 3% of original. If any washer fails, the whole batch gets reworked.
Lead Time and Tooling — No MOQ, Made in China
Prototype tooling takes 7 days, production tooling 15 days. Once the die is approved, first articles ship in 5 working days. We have no MOQ — order 10 pieces or 100,000, same quality control. Our factory in Dongguan runs 24/5, so rush orders (3-day lead) are possible with a 20% surcharge. All parts are made in China, but we ship DDP to the US and EU with full material certificates.
Parameter
Value
Material
Phosphor Bronze C5191, C5210
Thickness
0.1 – 2.0 mm
Outer Diameter
3 – 80 mm
Wave count
3, 5, or custom
Hardness
80 – 100 HRB (spring temper)
Thickness tolerance
±0.01 mm
Wave height tolerance
±0.03 mm
Surface finish
Ra 0.4 µm (vibratory finished)
Runout (concentricity)
≤0.05 mm TIR
Lead time
5 days (prototype), 15 days (tooling)
MOQ
No MOQ
What is your minimum order quantity for corrugated washers?
Zero — we take any quantity, from a single prototype to high-volume production, with no setup fee for orders above 500 pieces.
Can you customize wave count, diameter, or material temper?
Yes, we change wave count from 3 to 7, adjust outer diameter in 0.5 mm steps, and select C5191 or C5210 in half-hard, hard, or extra-hard temper based on your load requirement.
How do you ensure quality on a small batch of 50 washers?
Every washer in a batch under 1,000 pieces is measured individually with a CMM and a wave-height gauge; we send you a full inspection report with photos.
What is the typical lead time if I need 10,000 pieces?
Production tooling takes 15 days, then we stamp 10,000 pieces in 3 days — total 18 working days, or 12 days with our rush option.
For your next project, check our CNC cutting tool selection guide if you also plan to machine the mating part, and review our CNC machining tolerances guide to match stamping tolerances with your assembly. Both guides cover real shop-floor limits, not theoretical numbers.
Send us your drawing — DXF, STEP, or PDF — and we will return a firm quote within 12 hours. Email sc@bquq.com or WhatsApp +86 13713157787. Precision manufacturing is our only business, and BQUQ has done it for 20 years in Dongguan.
Straight answers from the factory, not a sales brochure.
How do I get a quote for this part?
Send your drawing (STEP, IGES, DWG, DXF or PDF) with quantity and target material to sc@bquq.com or WhatsApp +86 137 1315 7787. Our engineers review the drawing and reply with price, lead time and tooling cost.
What is your MOQ?
We do not set a fixed MOQ. The minimum is decided per part and per process, so tell us your target quantity and we quote against it. Small trial batches are accepted for new parts.
What is the lead time?
Lead time is agreed per order, based on the date you need, the quantity, the material and whether tooling is required. Send your target date with the drawing and we confirm what is achievable before you commit.
What tolerance can you hold?
CNC machining holds ±0.005 mm. Stamping, spring and extrusion parts are made to the tolerances marked on your drawing, and we confirm achievable values at quotation so there are no surprises at inspection.
Can you manufacture parts to my drawing?
Yes. Every order is made to the customer drawing or sample. We run CNC machining, metal stamping, spring coiling and aluminium heat sink extrusion in-house in Dongguan, so one supplier covers the whole part.
STEP, IGES, DWG, DXF and PDF. A 2D drawing with tolerances and surface finish requirements is preferred alongside the 3D model. Hand sketches can be quoted after our engineers redraw them.
How is quality controlled?
Inspection runs through the process, not only at the end: first article approval, in-process checks and a final report per batch, measured with CMM and optical equipment. Material certificates are available on request.
Where is the factory and do you ship worldwide?
Our factory is in Dongguan, Guangdong, China, operating since 2005. We ship worldwide by express, air and sea, and work with the forwarder nominated by the buyer.