BQUQ TV Wall Bracket Stamping: Precision Steel, ±0.05mm Tolerance
Why This TV Wall Bracket Holds Flat Without Shim Kits This TV Wall Bracket is a single-piece metal stamping formed from cold-rolled steel SPCC or stainless SUS304, not a welded assembly. The result:
Get a Fast Quote for This Part
Send us your drawing / quantity / material — reply within 24h.
Why This TV Wall Bracket Holds Flat Without Shim Kits
This TV Wall Bracket is a single-piece metal stamping formed from cold-rolled steel SPCC or stainless SUS304, not a welded assembly. The result: flatness within 0.1 mm across the mounting plate and parallel faces held to ±0.05 mm, so the bracket sits flush against drywall or concrete without shims. The stamping die leaves a clean shear edge, and we deburr every hole to 0.2 mm max edge radius—no sharp burrs that cut mounting cables. Typical production lead time is 12 days after die approval, and hardness on hardened variants reaches 45 HRC for load-bearing arms. This is precision manufacturing made in China, engineered for flat-panel TVs from 32 to 85 inches.
Material Grades and Surface Finish We Actually Use
We run three standard materials for this TV Wall Bracket: SPCC (cold-rolled steel) for indoor use, SECC (electro-galvanized) for humidity resistance, and SUS304 stainless for coastal or outdoor installations. Sheet thickness ranges from 1.2 mm to 3.0 mm, chosen by TV weight class. Surface finish is bright-annealed on stainless, or zinc-plated with clear passivation on steel—average Ra 1.6 µm on visible faces, Ra 0.8 µm on load-bearing surfaces. If you need powder coating, we apply 60 µm epoxy polyester, tested for 500 hours salt spray per ASTM B117.
Die Life and Stamping Tolerances on the Mounting Holes
The VESA hole pattern (100x100 to 600x400) is punched in a single die strike, not drilled. This keeps hole-to-hole pitch within ±0.05 mm, so screws align with TV inserts every time. Our progressive die runs at 40 strokes per minute, and we replace the punch after 300,000 hits to hold edge quality. If you need a custom VESA pattern, we modify the die insert—tooling changes cost from $800 and take 7 days. For a detailed breakdown of what affects stamping accuracy, see our CNC machining tolerances guide—the same principles apply to press tooling.
Load Rating and Hardness After Forming
We form the vertical arm with a 90° bend and a reinforcing rib, increasing section modulus by 30% compared to a flat strip. For 1.5 mm SPCC, the bracket holds 50 kg static load with 2.5x safety factor. For heavy 85-inch TVs, we use 2.5 mm SECC with a hardened pivot pin—surface hardness 45 HRC, core 35 HRC—so the tilt mechanism does not wear after 10,000 cycles. We test every batch to 1.5x rated load for 1 hour before packing. This TV Wall Bracket is not a generic stamping; it is a fatigue-tested component.
Inspection Before Every Shipment: CMM and Go/No-Go Gauges
Each lot of 500 brackets is inspected on a CMM (coordinate measuring machine) for flatness, hole pitch, and bend angle—we report actual values, not just pass/fail. In addition, we run a 100% visual check for burrs, scratches, and plating holidays. Every bracket gets a go/no-go gauge test on the VESA holes and the latch slot. We keep this QC log for 3 years, and you can request a copy with your shipment. If you are choosing between stamping and machining, read our CNC cutting tool selection guide—it explains why dies last longer than cutters for high-volume parts.
Packing, Marking, and Delivery for Export Orders
Brackets are packed in corrugated boxes with foam inserts, 20 pieces per box, then palletized with stretch wrap. Each box is marked with part number, lot code, and quantity. For orders under 500 pieces, we use standard export cartons; for larger orders, we add wooden pallets with ISPM-15 heat treatment. Sea freight from Shenzhen to Los Angeles takes 18 days; air freight takes 5 days. We ship DDP or EXW, and we provide a packing list and CO (certificate of origin) with every order.
Design for Stamping: What We Modify Free of Charge
If you send a drawing with sharp inner corners or deep draws, we will recommend changes—radius of 1.5x material thickness, draft angles, and slot widths that match our die. These modifications reduce tool wear and scrap, and we do this review free within 24 hours of receiving your file. We do not charge for DFM feedback, and we keep your design confidential under NDA. For low-volume prototypes, we use wire EDM to make a soft die, then switch to hard tooling once you approve.
Specification
Value / Range
Material
SPCC, SECC, SUS304 (thickness 1.2–3.0 mm)
VESA hole pattern
100x100 to 600x400 mm (custom on request)
Hole-to-hole pitch tolerance
±0.05 mm
Flatness (mounting plate)
0.1 mm max
Bend angle tolerance
±0.5°
Surface finish (steel)
Ra 1.6 µm; Ra 0.8 µm on load-bearing faces
Hardness (hardened pivot)
45 HRC surface, 35 HRC core
Static load rating
50 kg (2.5x safety factor)
Lead time (after die approval)
12 days for 1,000 pcs
MOQ
No MOQ—start from 1 piece
What is the minimum order quantity for this TV Wall Bracket?
No MOQ—we accept orders from 1 piece for prototyping, with per-unit pricing that drops at 500, 1,000, and 5,000 pieces.
Can you match my exact VESA hole pattern and arm length?
Yes, we modify the die insert for custom hole patterns and arm lengths—tooling changes cost from $800 and take 7 days, with free DFM feedback before you commit.
How do you guarantee quality across different batches?
We use CMM inspection on every lot of 500, 100% visual checks, and go/no-go gauges on all critical holes—plus we keep QC logs for 3 years and share them on request.
What is the typical lead time for a production order?
12 days after die approval for 1,000 pieces, including stamping, deburring, plating, and packing—air freight to the US takes 5 additional days.
Send your drawing for a firm quote within 12 hours—no MOQ, precision manufacturing made in China. Email sc@bquq.com or WhatsApp +86 13713157787. We reply in English, with DFM comments and a per-unit price table.
Straight answers from the factory, not a sales brochure.
How do I get a quote for this part?
Send your drawing (STEP, IGES, DWG, DXF or PDF) with quantity and target material to sc@bquq.com or WhatsApp +86 137 1315 7787. Our engineers review the drawing and reply with price, lead time and tooling cost.
What is your MOQ?
We do not set a fixed MOQ. The minimum is decided per part and per process, so tell us your target quantity and we quote against it. Small trial batches are accepted for new parts.
What is the lead time?
Lead time is agreed per order, based on the date you need, the quantity, the material and whether tooling is required. Send your target date with the drawing and we confirm what is achievable before you commit.
What tolerance can you hold?
CNC machining holds ±0.005 mm. Stamping, spring and extrusion parts are made to the tolerances marked on your drawing, and we confirm achievable values at quotation so there are no surprises at inspection.
Can you manufacture parts to my drawing?
Yes. Every order is made to the customer drawing or sample. We run CNC machining, metal stamping, spring coiling and aluminium heat sink extrusion in-house in Dongguan, so one supplier covers the whole part.
STEP, IGES, DWG, DXF and PDF. A 2D drawing with tolerances and surface finish requirements is preferred alongside the 3D model. Hand sketches can be quoted after our engineers redraw them.
How is quality controlled?
Inspection runs through the process, not only at the end: first article approval, in-process checks and a final report per batch, measured with CMM and optical equipment. Material certificates are available on request.
Where is the factory and do you ship worldwide?
Our factory is in Dongguan, Guangdong, China, operating since 2005. We ship worldwide by express, air and sea, and work with the forwarder nominated by the buyer.