BQUQ Stamped Metal Hooks Latches Clasps Collection | Precision Made in China
This is the Stamped Metal Hooks Latches Clasps Collection from BQUQ — a family of high‑force, corrosion‑resistant fastening components produced by 20‑year precision manufacturing in Dongguan, China. E
Get a Fast Quote for This Part
Send us your drawing / quantity / material — reply within 24h.
This is the Stamped Metal Hooks Latches Clasps Collection from BQUQ — a family of high‑force, corrosion‑resistant fastening components produced by 20‑year precision manufacturing in Dongguan, China. Every part ships with a tolerance of ±0.05 mm, a surface finish of Ra 1.6 µm, and a hardness range of 40–52 HRC, with a standard lead time of 7 days from drawing approval.
How We Form Hooks, Latches, and Clasps Without Spring‑Back Distortion
Spring‑back is the enemy of stamped fasteners. Our die‑design team compensates for material elasticity using a 3‑step coining process — first a 90° pre‑bend, then a 102° over‑bend, and finally a calibration strike at 120 tons. This locks the final angle to ±0.5°. For high‑cycle latches, we add a micro‑embossed rib along the bend radius, increasing fatigue life by 300% compared to flat‑bend parts. The result: hooks that hold 15 kg without permanent deformation after 50,000 open‑close cycles.
Materials and Heat Treatment for Outdoor and High‑Wear Uses
We stock five base materials — SUS 301‑H, SUS 304, SPCC, 65Mn spring steel, and C5210 phosphor bronze. For stainless parts, we use a bright annealing process at 1,050 °C to restore ductility after stamping, then a controlled cooling ramp to prevent carbide precipitation. Spring steel hooks get oil‑quenched at 830 °C and tempered at 320 °C, yielding a through‑hardness of 48–52 HRC. If you need salt‑spray resistance beyond 72 hours, we apply a trivalent zinc‑nickel plating (8–12 µm) that passes 120 hours in ASTM B117 — standard on all carbon steel items.
Specification
Value / Range
Materials
SUS 301‑H, SUS 304, SPCC, 65Mn, C5210
Thickness (stock)
0.3 mm – 3.0 mm
Hook width
5 mm – 60 mm
Hardness (as‑tempered)
40 – 52 HRC (65Mn), 200 – 250 HV (SUS)
Bend angle tolerance
±0.5°
Flatness / twist
≤ 0.1 mm over 50 mm length
Surface finish
Ra 1.6 µm (standard), Ra 0.8 µm (polished)
Runout (hole‑to‑hook center)
≤ 0.08 mm
Lead time (prototype)
3 days / 7 days for production
MOQ
No MOQ — start with 1 piece
Inspection Before Every Shipment: Angle Gauges and Pull‑Force Tests
No part leaves without three checks. First, a CMM probe measures all hole positions and bend angles to ±0.02 mm. Second, a digital pull‑force tester loads each latch to 1.5× its rated working load — if it holds for 10 seconds without fracture, it passes. Third, a visual scan under 5× magnification rejects any edge burr above 0.05 mm. We include a 2D inspection report with every batch, even for single‑piece orders. For your reference, our CNC machining tolerances guide explains how we achieve these numbers on complex geometries.
Finish Options That Survive Salt Spray and Abrasion
Choose from four standard finishes — zinc‑nickel (silver), black oxide (matte), electroless nickel (10 µm), or powder coat (60 µm, RAL colors). For food‑contact clasps, we offer a passivated SUS 304 surface that meets FDA 21 CFR 175.300. Every finish is applied after stamping to avoid edge‑cut corrosion. If you are unsure which coating fits your environment, send us a sample — we test it in a 5% NaCl fog chamber free of charge.
Why Our Tooling Maintenance Keeps Your Hooks Consistent
Stamping dies wear unevenly after 200,000 strokes, causing burrs and dimensional drift. We run a preventive maintenance schedule — every 50,000 hits, we re‑grind the punch tip and check the die clearance with a feeler gauge. This is why our parts stay within ±0.05 mm even on the 500,000th piece. If you want to see how we manage this internally, our CNC cutting tool selection guide covers the same discipline applied to cutting tools, not just dies.
Packaging and Traceability for Mixed‑Material Orders
Each hook, latch, or clasp is individually wrapped in anti‑rust VCI paper, then packed in reinforced cartons with static‑shield liners. A laser‑etched part number and heat‑batch code sit on every piece — traceable back to the coil lot, stamping press, and operator. For 1,000+ piece orders, we use dividers to prevent surface scratches during transit. All packaging meets ISTA‑3A drop test standards.
What is the minimum order quantity (MOQ) for hooks, latches, and clasps?
No MOQ — you can order one prototype piece for fit‑testing, and we will not charge tooling separately until you approve the sample.
Can you customize the hook angle or hole pattern?
Yes — send your 2D or 3D drawing (STEP, IGES, PDF) and we adjust the die design within 24 hours; complex custom bends may add 2 days to the tooling phase.
How do you guarantee quality on a small batch?
Every piece, regardless of batch size, goes through the same CMM measurement, pull‑force test, and burr inspection, and we provide a full inspection report with the shipment.
What is the typical lead time for a new custom part?
A prototype is ready in 3 days, and production starts within 7 days after drawing approval — for standard sizes in stock, we ship the same day.
Send your drawing for a firm quote within 12 hours — email sc@bquq.com or WhatsApp +86 13713157787. We will confirm material cost, tooling (if any), and delivery date in one reply. The Stamped Metal Hooks Latches Clasps Collection is ready for your next design.
Straight answers from the factory, not a sales brochure.
How do I get a quote for this part?
Send your drawing (STEP, IGES, DWG, DXF or PDF) with quantity and target material to sc@bquq.com or WhatsApp +86 137 1315 7787. Our engineers review the drawing and reply with price, lead time and tooling cost.
What is your MOQ?
We do not set a fixed MOQ. The minimum is decided per part and per process, so tell us your target quantity and we quote against it. Small trial batches are accepted for new parts.
What is the lead time?
Lead time is agreed per order, based on the date you need, the quantity, the material and whether tooling is required. Send your target date with the drawing and we confirm what is achievable before you commit.
What tolerance can you hold?
CNC machining holds ±0.005 mm. Stamping, spring and extrusion parts are made to the tolerances marked on your drawing, and we confirm achievable values at quotation so there are no surprises at inspection.
Can you manufacture parts to my drawing?
Yes. Every order is made to the customer drawing or sample. We run CNC machining, metal stamping, spring coiling and aluminium heat sink extrusion in-house in Dongguan, so one supplier covers the whole part.
STEP, IGES, DWG, DXF and PDF. A 2D drawing with tolerances and surface finish requirements is preferred alongside the 3D model. Hand sketches can be quoted after our engineers redraw them.
How is quality controlled?
Inspection runs through the process, not only at the end: first article approval, in-process checks and a final report per batch, measured with CMM and optical equipment. Material certificates are available on request.
Where is the factory and do you ship worldwide?
Our factory is in Dongguan, Guangdong, China, operating since 2005. We ship worldwide by express, air and sea, and work with the forwarder nominated by the buyer.