BQUQ Zinc Plated Stamped Spring Clips Collection | Precision Metal Stamping
This collection covers stamped spring clips in zinc-plated carbon steel, engineered for retention and vibration resistance in assemblies from automotive brackets to consumer electronics. We hold flatn
Get a Fast Quote for This Part
Send us your drawing / quantity / material — reply within 24h.
This collection covers stamped spring clips in zinc-plated carbon steel, engineered for retention and vibration resistance in assemblies from automotive brackets to consumer electronics. We hold flatness to 0.05mm and hole-to-hole positioning to ±0.05mm, with a surface finish of Ra 1.6 after plating. Hardness is controlled at 45-50 HRC post heat treatment, and standard production ships in 15 days from drawing approval.
Why Our Spring Clips Hold Better Than Bent Wire
Bent wire clips deform under cyclic load. Stamped clips do not. Our progressive dies produce a uniform grain flow along the clip's bend radius, eliminating stress risers. Each clip's spring rate is verified on a load tester—we hold a ±5% variance on the force-to-deflection curve. If your design requires a retention force of 12N at 1.5mm deflection, we deliver that within 0.6N, clip after clip.
Zinc Plating Thickness and Salt Spray Hours
Zinc plating is not a single spec. We offer clear, yellow, or blue passivation. Standard thickness is 8-12 microns, which passes 72 hours of neutral salt spray testing per ASTM B117. For outdoor or underhood applications, we add a trivalent seal that pushes corrosion resistance to 120 hours without affecting the clip's dimensional envelope. Plating is applied after heat treatment, so the spring temper is not compromised.
Materials and Heat Treatment We Use
We stock three base materials: C75S (1.1248) spring steel, 65Mn, and 301 stainless for high-temperature zones. The C75S clips are oil-quenched and tempered to 45-50 HRC. We do not use case hardening—that only hardens the skin and leaves a soft core. Through-hardening gives you a consistent spring modulus across the entire cross-section. For thin clips under 0.8mm thickness, we use 65Mn with a modified tempering cycle to prevent brittleness.
Tooling Precision That Determines Your Assembly Speed
Your production line stops when clips jam in feeders or misalign in fixtures. Our die clearances are held to 5% of material thickness, which produces a clean shear zone with minimal burr. Burr height is capped at 0.03mm—measured on a comparator before every lot ships. If your clip has a critical locating slot, we hold that dimension to ±0.02mm using wire-cut tooling inserts. This is what makes our Zinc Plated Stamped Spring Clips Collection feel like a drop-in replacement, not a rework project.
Inspection Before Every Shipment
Every batch goes through a three-stage check. First, a coordinate measuring machine (CMM) verifies critical geometry on five pieces from the first run. Second, a hardness test is performed on a Rockwell scale—we reject any piece below 45 HRC. Third, a random sample of 0.5% of the lot is visually inspected under a 10x magnifier for plating voids or edge tears. We send you a PDF inspection report with the shipment, including salt spray results and material certs. If you want a full lot inspection, we offer that at no extra charge for orders under 5,000 pieces.
Zinc Plated Stamped Spring Clips Collection: Typical Spec Table
Parameter
Value / Range
Notes
Materials
C75S, 65Mn, 301 SS
Strip thickness 0.2–3.0mm
Hardness
45–50 HRC
Through-hardened, oil quenched
Dimensional Tolerance
±0.05mm
Critical features ±0.02mm
Flatness
0.05mm max
After plating, measured on granite plate
Surface Finish (Ra)
Ra 1.6
As-stamped, before plating
Burr Height
≤0.03mm
Per DIN 2670 Part 1
Plating Thickness
8–12 microns
Clear / yellow / blue zinc
Salt Spray Resistance
72–120 hours
ASTM B117, depends on passivation
Lead Time
15 days
From drawing approval, standard stock sizes
MOQ
No MOQ
Prototypes accepted from 1 piece
Why 65Mn and C75S Beat Stainless for Cost-Critical Clips
Stainless steel costs 3x more per kilogram and work-hardens during stamping, which shortens die life. For zinc plated clips inside a housing or bracket, carbon steel is the smart choice. C75S gives you a higher fatigue limit than 65Mn, but 65Mn is easier to form for complex geometric features. We help you pick the right grade based on your operating temperature and cycle count. If you are unsure, send us your deflection and load requirements—we will suggest a material and simulate the spring rate in our FEA software.
Frequently Asked Questions
What is the minimum order quantity for the Zinc Plated Stamped Spring Clips Collection?
No MOQ—we accept prototype orders from one piece and scale to millions per year.
Can you customize the zinc plating color or add a sealant?
Yes, we offer clear, yellow, blue, and black zinc, plus a trivalent seal for higher corrosion resistance.
How do you ensure quality control on stamping tolerances?
We use CMM inspection on first-run pieces, Rockwell hardness testing on every batch, and a 0.5% random visual inspection per lot.
What is the typical lead time for a custom spring clip?
Tooling takes 10 days, and production takes 5 days after approval—15 days total for standard materials.
How to Spec Your Clip for a Fast Quote
Send us a 2D PDF and 3D STEP file. We need the material thickness, the maximum operating temperature, and the required spring force at a given deflection. If you do not have a drawing, send us a sample part and we will reverse-engineer it within 48 hours. We have built over 2,000 progressive dies for spring clips since 2004. This is not our first time seeing an unusual bend radius or a tight tolerance. Our engineers will flag any feature that risks cracking during bending and suggest a die-radius adjustment. This precision manufacturing approach is what has kept our clients in the automotive and appliance sector reordering for 15 years.
Send your drawing to sc@bquq.com or message us on WhatsApp at +86 13713157787. We reply with a firm quote—not a ballpark—within 12 hours on business days. Include your annual volume, target price per piece, and any plating requirement. We will send you a DFM feedback sheet and a sample of our inspection checklist. Made in China, engineered for global OEMs. No MOQ, no surprises.
Straight answers from the factory, not a sales brochure.
How do I get a quote for this part?
Send your drawing (STEP, IGES, DWG, DXF or PDF) with quantity and target material to sc@bquq.com or WhatsApp +86 137 1315 7787. Our engineers review the drawing and reply with price, lead time and tooling cost.
What is your MOQ?
We do not set a fixed MOQ. The minimum is decided per part and per process, so tell us your target quantity and we quote against it. Small trial batches are accepted for new parts.
What is the lead time?
Lead time is agreed per order, based on the date you need, the quantity, the material and whether tooling is required. Send your target date with the drawing and we confirm what is achievable before you commit.
What tolerance can you hold?
CNC machining holds ±0.005 mm. Stamping, spring and extrusion parts are made to the tolerances marked on your drawing, and we confirm achievable values at quotation so there are no surprises at inspection.
Can you manufacture parts to my drawing?
Yes. Every order is made to the customer drawing or sample. We run CNC machining, metal stamping, spring coiling and aluminium heat sink extrusion in-house in Dongguan, so one supplier covers the whole part.
STEP, IGES, DWG, DXF and PDF. A 2D drawing with tolerances and surface finish requirements is preferred alongside the 3D model. Hand sketches can be quoted after our engineers redraw them.
How is quality controlled?
Inspection runs through the process, not only at the end: first article approval, in-process checks and a final report per batch, measured with CMM and optical equipment. Material certificates are available on request.
Where is the factory and do you ship worldwide?
Our factory is in Dongguan, Guangdong, China, operating since 2005. We ship worldwide by express, air and sea, and work with the forwarder nominated by the buyer.