Precision Metal Heat Sink by BQUQ | CNC Machined, Made in China
This is a CNC-machined Metal Heat Sink built for active and passive cooling of high-power electronics, power modules, and laser diodes. You get a flatness of 0.02mm across the mounting surface, a surf
Get a Fast Quote for This Part
Send us your drawing / quantity / material — reply within 24h.
This is a CNC-machined Metal Heat Sink built for active and passive cooling of high-power electronics, power modules, and laser diodes. You get a flatness of 0.02mm across the mounting surface, a surface finish of Ra 0.8µm, and a straightness tolerance of ±0.01mm per 100mm—all verified before shipment. Lead time is 15 days for standard aluminum alloys, and we hold a hardness of 63 HRC on steel-based sinks where structural rigidity matters.
Why Flatness and Surface Finish Determine Your Thermal Junction Temperature
Every 0.05mm of air gap between your IGBT and the sink adds roughly 0.5°C/W of thermal resistance. Our CNC milling and fly-cutting process holds the base flatness to 0.02mm, so you do not need thermal paste thicker than 0.05mm. We measure each surface with a coordinate measuring machine (CMM) and a profilometer. The result: a predictable thermal path for your 200W to 2kW heat loads.
Aluminum 6061-T6, 5052, or Copper C1100—What We Machine Daily
We stock 6061-T6 with a yield strength of 276 MPa and thermal conductivity of 167 W/m·K. For higher conductivity, we use C1100 copper at 391 W/m·K, but we recommend anodized aluminum for weight-sensitive designs. All raw material comes with mill certificates. We reject any plate that shows internal voids or inconsistent grain structure before cutting.
Fins, Pins, and Skived Geometry—How We Machine Without Burrs
We use a 3-axis and 5-axis CNC milling center to produce straight fins, pin fins, or dovetail slots. For fin pitches below 2.5mm, we switch to a custom saw-blade cutter that reduces burr formation. After machining, we tumble every part for 30 minutes to remove micro-burrs that your assembly line would otherwise catch. We also offer a skiving process for fins as thin as 0.8mm, which gives you 30% more surface area than extrusion.
Inspection Before Every Shipment—CMM, Air Gauge, and Leak Test
Every batch goes through a 3-point check. First, a CMM measures critical mounting holes and base flatness. Second, an air gauge verifies hole diameters to ±0.01mm. Third, for liquid-cooled versions, we perform a 0.6 MPa air leak test under water. We send you a PDF inspection report with each shipment. If a part fails, we scrap it on the floor—not in your incoming quality check.
Anodizing, Ni-Plating, or Passivation—Your Corrosion and Insulation Options
We offer Class 2 black anodizing (18–20 µm thickness) for aluminum, which adds dielectric strength of up to 800V. For copper, we provide electroless nickel plating to prevent oxidation at high humidity. If you need a bare surface for maximum thermal conductivity, we ship it with a VCI anti-corrosion paper and sealed poly bags. We do not apply any coating without your written approval.
How We Handle Your Prototype—From One Piece to 5,000 with No MOQ
Send a STEP or IGES file, and we generate a DFM report within 24 hours. For a single prototype, we use the same CNC program as production, so you get identical geometry. We do not charge tooling fees for standard shapes. Only if you require a new skiving blade or custom fixture, we quote a one-time cost of $200–$800, which is waived once you order over 500 pieces.
What is the minimum order quantity?
We operate with no MOQ—you can order one piece for testing, and the unit price is only 15% higher than at 1,000 pieces.
Can you customize the fin pattern for my specific airflow direction?
Yes, we machine any fin pattern—straight, pin, or offset—based on your CFD data, and we will suggest a fin pitch based on your fan curve.
How do you guarantee the flatness of the mounting surface?
We measure flatness on a granite table with a dial indicator at 9 points, and we provide the CMM report before shipping.
What is the lead time for a copper heat sink prototype?
Copper prototypes take 20 days because of longer machining time and additional deburring steps, but we can rush it to 12 days for an extra 10% fee.
Material Selection Guide—Read Before You Send Your Drawing
If you are unsure whether to use 6061-T6 or copper, check our CNC cutting tool selection guide for tips on machinability and tool wear. For tolerance decisions, read our CNC machining tolerances guide to see what is achievable without driving up cost. Both guides are written by our shop floor engineers, not marketing staff.
We are a precision manufacturing factory in Dongguan, China, with 20 years of experience in CNC machining, stamping, and springs. Our heat sinks have shipped to 14 countries for use in EV chargers, medical lasers, and industrial inverters. We keep our process simple: you send a drawing, we quote in 12 hours, and we ship with full inspection data.
Send your drawing for a firm quote within 12 hours. Email sc@bquq.com or WhatsApp +86 13713157787. Mention "Metal Heat Sink" in the subject line, and we will prioritize your DFM review.
Straight answers from the factory, not a sales brochure.
How do I get a quote for this part?
Send your drawing (STEP, IGES, DWG, DXF or PDF) with quantity and target material to sc@bquq.com or WhatsApp +86 137 1315 7787. Our engineers review the drawing and reply with price, lead time and tooling cost.
What is your MOQ?
We do not set a fixed MOQ. The minimum is decided per part and per process, so tell us your target quantity and we quote against it. Small trial batches are accepted for new parts.
What is the lead time?
Lead time is agreed per order, based on the date you need, the quantity, the material and whether tooling is required. Send your target date with the drawing and we confirm what is achievable before you commit.
What tolerance can you hold?
CNC machining holds ±0.005 mm. Stamping, spring and extrusion parts are made to the tolerances marked on your drawing, and we confirm achievable values at quotation so there are no surprises at inspection.
Can you manufacture parts to my drawing?
Yes. Every order is made to the customer drawing or sample. We run CNC machining, metal stamping, spring coiling and aluminium heat sink extrusion in-house in Dongguan, so one supplier covers the whole part.
STEP, IGES, DWG, DXF and PDF. A 2D drawing with tolerances and surface finish requirements is preferred alongside the 3D model. Hand sketches can be quoted after our engineers redraw them.
How is quality controlled?
Inspection runs through the process, not only at the end: first article approval, in-process checks and a final report per batch, measured with CMM and optical equipment. Material certificates are available on request.
Where is the factory and do you ship worldwide?
Our factory is in Dongguan, Guangdong, China, operating since 2005. We ship worldwide by express, air and sea, and work with the forwarder nominated by the buyer.