BQUQ Cnc Machined Pump Impellers | Precision Manufacturing in China
What You Get: A Pump Impeller That Balances at 0.02 mm Runout This is a CNC machined pump impeller, cut from solid bar or billet, not cast. The benefit is simple: you get a vane profile that holds ±
Get a Fast Quote for This Part
Send us your drawing / quantity / material — reply within 24h.
What You Get: A Pump Impeller That Balances at 0.02 mm Runout
This is a CNC machined pump impeller, cut from solid bar or billet, not cast. The benefit is simple: you get a vane profile that holds ±0.005 mm tolerance and 0.02 mm total runout. That means less vibration, longer seal life, and higher pump efficiency. We ship standard lead time of 15 days, with hardness up to 45 HRC for abrasive fluids.
Why We Cut Impellers From Solid Bar Instead of Casting
Cast impellers have internal porosity and inconsistent vane thickness. We machine from 6061-T6 aluminum, 316L stainless, or duplex 2205. The tool path removes material in a spiral roughing sequence, then a 0.2 mm finish pass. The result: a vane surface with Ra 0.8 µm, no draft angle, and no hidden voids. You design the 3D profile; we hold it to the model, not to a pattern.
Five-Axis Machining for Twisted Vanes and Tight Exit Angles
Most pump impellers have twisted vanes that a 3-axis mill cannot reach without re-fixturing. We use 5-axis simultaneous machining. This means the tool tilts to keep a constant chip load on the vane's pressure side and suction side. We can machine exit angles as steep as 15 degrees without leaving a witness line. For closed impellers, we use a custom stub-length end mill with a 0.5 mm corner radius to access the shroud gap.
Balancing and Runout: The Numbers That Stop Cavitation
Unbalanced impellers cause shaft fatigue and seal wear. We do a two-plane dynamic balance on every impeller above 100 mm diameter. The limit is G2.5 per ISO 1940-1, which translates to 0.02 mm runout at the hub bore. For high-speed pumps (over 3000 RPM), we offer G1.0 balancing as a standard option. We also grind the hub bore to H7 fit after machining, so your shaft insertion is repeatable.
Materials and Heat Treatment We Use for Abrasive or Corrosive Duty
For clean water, 6061-T6 aluminum is fine. For seawater, we use 316L or super duplex 2507. For slurry pumps, we machine from 17-4 PH stainless, then heat treat to 45 HRC. Hard coating options include electroless nickel (50 µm) and tungsten carbide spray (300 µm) for sand-laden fluids. We do not cast, so you get the full wrought material density — no micro-porosity, no sand inclusions.
Inspection Before Every Shipment: CMM and Flow Test Data
Every impeller goes through a Zeiss CMM with a 0.5 µm probe. We check vane thickness at 10 points per blade, hub bore diameter, and face runout. For critical jobs, we include a written report with the actual measured values. We also do a dye penetrant test on stainless parts to confirm no surface cracks. You get the data file, not just a certificate.
Lead Time and Shipping: 15 Days Standard, 7 Days Rush
Standard lead time is 15 working days from drawing approval. For a rush order of up to 50 pieces, we can do 7 days with a 20% surcharge. We ship via DHL or FedEx for small batches, or sea freight for over 200 kg. Every impeller is wrapped in VCI paper and boxed in foam — no bare metal contact during transit. We also mark the part with a laser-etched batch number inside the hub bore.
No MOQ — we machine a single prototype impeller for testing, then scale to production after approval.
Can you machine my custom vane profile from a STEP file?
Yes, send any STEP, IGES, or Parasolid file; our engineers check for tool access and suggest a modified tool path if the vane angle exceeds 15 degrees.
How do you verify the impeller is within tolerance before shipping?
We use a Zeiss CMM to measure vane thickness, bore diameter, and runout, and we include the measured report with every shipment.
What is the fastest lead time for a small batch?
For up to 50 pieces, we can ship in 7 working days with a rush surcharge, but standard 15-day lead time is preferred to maintain full quality checks.
Send your impeller drawing to sc@bquq.com or WhatsApp +86 13713157787. We reply with a firm quote and DFM feedback within 12 hours. No MOQ, no hidden tooling fees, just precision manufacturing made in China.
Straight answers from the factory, not a sales brochure.
How do I get a quote for this part?
Send your drawing (STEP, IGES, DWG, DXF or PDF) with quantity and target material to sc@bquq.com or WhatsApp +86 137 1315 7787. Our engineers review the drawing and reply with price, lead time and tooling cost.
What is your MOQ?
We do not set a fixed MOQ. The minimum is decided per part and per process, so tell us your target quantity and we quote against it. Small trial batches are accepted for new parts.
What is the lead time?
Lead time is agreed per order, based on the date you need, the quantity, the material and whether tooling is required. Send your target date with the drawing and we confirm what is achievable before you commit.
What tolerance can you hold?
CNC machining holds ±0.005 mm. Stamping, spring and extrusion parts are made to the tolerances marked on your drawing, and we confirm achievable values at quotation so there are no surprises at inspection.
Can you manufacture parts to my drawing?
Yes. Every order is made to the customer drawing or sample. We run CNC machining, metal stamping, spring coiling and aluminium heat sink extrusion in-house in Dongguan, so one supplier covers the whole part.
STEP, IGES, DWG, DXF and PDF. A 2D drawing with tolerances and surface finish requirements is preferred alongside the 3D model. Hand sketches can be quoted after our engineers redraw them.
How is quality controlled?
Inspection runs through the process, not only at the end: first article approval, in-process checks and a final report per batch, measured with CMM and optical equipment. Material certificates are available on request.
Where is the factory and do you ship worldwide?
Our factory is in Dongguan, Guangdong, China, operating since 2005. We ship worldwide by express, air and sea, and work with the forwarder nominated by the buyer.