Custom CNC Collet Chuck 700 Type Round Bore Auto Lathe Made in China
OpeningYour drawing defines the part. We machine it to spec and verify it before shipment. No guesswork, no tolerance gambling.This is a 700 Type round bore spring collet chuck for auto lathes. It is
Get a Fast Quote for This Part
Send us your drawing / quantity / material — reply within 24h.
Your drawing defines the part. We machine it to spec and verify it before shipment. No guesswork, no tolerance gambling.
This is a 700 Type round bore spring collet chuck for auto lathes. It is built for high-speed, high-repeatability gripping. We make it from your print, in the exact material and hardness you specify.
1. Batch-traceable quality. Every lot gets a unique batch number. We record material heat number, heat treatment curve, and final inspection data. If a problem appears in your line, we trace it back to the exact batch in minutes.
2. Inspection report per batch. You get a full dimensional report with every shipment. Not a generic certificate – actual measured values for bore diameter, concentricity, hardness, and surface finish. Our QC team uses CMM, optical comparators, and Rockwell hardness testers.
3. One factory for CNC + stamping + spring + heat sink. Your collet chuck is not an isolated part. Many buyers also need springs, stampings, or heat sinks for the same assembly. We run all four lines under one roof. You send one drawing package, get one quote, one quality standard, one shipping schedule.
Where these parts are used
The 700 Type round bore spring collet chuck is a workhorse in precision manufacturing. Common applications:
Swiss-type lathe workholding – gripping bar stock from Ø 3 mm to Ø 40 mm for medical screws, dental implants, and watch parts.
CNC turning centers – secondary operations on pre-machined blanks where concentricity below 0.01 mm is mandatory.
Automotive fuel injector components – high-volume production where collet wear directly affects scrap rate.
Electronics connector pins – small diameter, high-speed machining with minimal runout.
Aerospace fasteners – where material traceability and hardness consistency are audited.
These chucks run at 6,000–10,000 RPM. They grip and release millions of cycles. The spring steel temper and slot geometry are what keep them accurate over that life. We control both.
Q: What is your MOQ?
A: No MOQ. We make one prototype for your validation, then scale to your production volume. Tooling is included in the piece price for small batches.
Q: How do you guarantee tolerance and quality?
A: We inspect 100% of critical dimensions on every piece. For batches over 500 pcs, we use SPC sampling on top of full inspection. You receive the measured report, not a promise.
Q: What is the lead time for a custom CNC collet chuck?
A: 15 working days for a sample (1–5 pcs). 20 working days for production batches. If you need faster, we can split the order and ship partial lots.
Q: Can you provide material certificates and heat treatment reports?
A: Yes. We supply mill certificates for raw material and a heat treatment curve with hardness values for every batch. Third-party testing (SGS, BV) is available at your cost.
Send your drawing
Get a firm quote within 12 hours. We review your print for manufacturability, suggest improvements if needed, and confirm price and lead time in one email.
Straight answers from the factory, not a sales brochure.
How do I get a quote for this part?
Send your drawing (STEP, IGES, DWG, DXF or PDF) with quantity and target material to sc@bquq.com or WhatsApp +86 137 1315 7787. Our engineers review the drawing and reply with price, lead time and tooling cost.
What is your MOQ?
We do not set a fixed MOQ. The minimum is decided per part and per process, so tell us your target quantity and we quote against it. Small trial batches are accepted for new parts.
What is the lead time?
Lead time is agreed per order, based on the date you need, the quantity, the material and whether tooling is required. Send your target date with the drawing and we confirm what is achievable before you commit.
What tolerance can you hold?
CNC machining holds ±0.005 mm. Stamping, spring and extrusion parts are made to the tolerances marked on your drawing, and we confirm achievable values at quotation so there are no surprises at inspection.
Can you manufacture parts to my drawing?
Yes. Every order is made to the customer drawing or sample. We run CNC machining, metal stamping, spring coiling and aluminium heat sink extrusion in-house in Dongguan, so one supplier covers the whole part.
STEP, IGES, DWG, DXF and PDF. A 2D drawing with tolerances and surface finish requirements is preferred alongside the 3D model. Hand sketches can be quoted after our engineers redraw them.
How is quality controlled?
Inspection runs through the process, not only at the end: first article approval, in-process checks and a final report per batch, measured with CMM and optical equipment. Material certificates are available on request.
Where is the factory and do you ship worldwide?
Our factory is in Dongguan, Guangdong, China, operating since 2005. We ship worldwide by express, air and sea, and work with the forwarder nominated by the buyer.