Custom CNC Machined Auto Lathe 15 Type Hex Bore Spring Collet | BQUQ
OpeningThis is a 15-type hex bore spring collet, machined to your exact drawing. We do not stock generic blanks and modify them. We start from raw bar stock and cut every feature—bore, hex, slots, and
Get a Fast Quote for This Part
Send us your drawing / quantity / material — reply within 24h.
This is a 15-type hex bore spring collet, machined to your exact drawing. We do not stock generic blanks and modify them. We start from raw bar stock and cut every feature—bore, hex, slots, and taper—to your specified tolerances. Each collet is verified before shipment, not sampled.
At a glance: Tolerance ±0.005 mm on bore and hex, surface finish Ra 0.4, lead time 7–12 days, no MOQ, material certs included.
You send the drawing. We machine the collet. You receive a part that fits your auto lathe spindle and holds your hex stock without chatter.
Specifications
Parameter
Value
Material options
65Mn spring steel, 60Si2MnA, 9Cr18 stainless, 40CrMo (hardened)
100% dimensional check, batch hardness test, taper gauge test
Batch size
1 piece to 10,000 pieces
Lead time
7 days (1–50 pcs), 12 days (50–500 pcs)
MOQ
None—single piece accepted
Certifications
Material mill cert, heat treatment report, dimensional inspection report
We use wire EDM for the relief slots, not milling. This gives a cleaner cut, no burr, and consistent slot width across the batch. The taper is ground after heat treatment, not before, so the geometry does not distort.
Three Reasons Buyers Send Us Their Drawings
1. Batch-traceable quality. Every collet gets a unique batch number. That batch number ties to the material heat number, the machine operator, the heat treatment furnace log, and the final inspection data. If you have a problem on your line six months from now, we can pull the exact records for that batch and tell you what happened. No guesswork.
2. Inspection report per batch. You do not have to trust our word. Each batch ships with a dimensional report listing every critical feature—bore size, hex across flats, taper angle, concentricity, hardness. The report is signed by the QC engineer, not a machine. If you need a third-party inspection (SGS, TÜV), we arrange it at cost.
3. One factory for CNC + stamping + springs + heat sinks. You are not our only product line. We run CNC machining, metal stamping, spring coiling, and heat sink fabrication under one roof. If your collet is part of a larger assembly—say a spring-loaded chuck or a heat-sinked spindle—you send us the whole package. One purchase order, one shipping point, one quality system. Fewer suppliers means fewer arguments about who is responsible when something does not fit.
Where These Parts Are Used
This 15-type hex bore spring collet is used in automatic lathes (Swiss-type and cam-type) that feed hex bar stock. Typical applications:
Hex fasteners: Holding hex stock for machining bolt heads, nuts, and set screws on CNC screw machines.
Brass and copper fittings: Gripping hexagonal brass bar for valve bodies, pipe fittings, and electrical terminals.
Medical device components: Small titanium and stainless hex parts for surgical instruments and bone screws, where concentricity matters.
Automotive fuel systems: Machining hex-shaped sensor housings and injector bodies from 60Si2MnA steel.
Aerospace fasteners: High-tolerance hex bolts and inserts where the collet must hold the stock without marking it.
The 15-type designation refers to the collet body size and taper, which matches common auto lathe spindles. If you are not sure whether your machine takes a 15-type, send us your spindle drawing or the old collet. We will confirm.
Q: What is your MOQ?
A: No MOQ. We machine one piece if that is what you need. The price per piece is higher for a single unit, but the tooling and setup are the same. For 100 pieces, the unit price drops significantly. Ask for a quote at both quantities.
Q: How do you guarantee tolerance and quality?
A: We cut the bore and hex on a CNC lathe with a live tool, then grind the taper after heat treatment. Final inspection is done on a CMM and a taper gauge. Every piece is checked, not just the first and last. The inspection report is included with the shipment.
Q: What is your lead time for custom CNC collet chuck?
A: 7 days for up to 50 pieces, 12 days for up to 500 pieces. If you need it faster, we can run a rush order for an additional 20% surcharge, subject to machine availability. We do not quote a lead time we cannot meet.
Q: Do you provide material certificates?
A: Yes. Every batch ships with a mill certificate for the raw material, a heat treatment report, and a hardness test certificate. If your customer requires EN 10204 3.1 or 3.2, we can provide it for an additional fee.
Send Your Drawing
Send us your drawing in PDF, STEP, or IGES format. We will review the tolerances, confirm the material, and send you a firm quote within 12 hours. No obligation, no hidden tooling charges. We are a precision manufacturing factory in Dongguan, China, with 20 years of experience in CNC machining, stamping, springs, and heat sinks. Your custom CNC collet chuck is made in China, but it is made to your exact spec, not a local standard.
Straight answers from the factory, not a sales brochure.
How do I get a quote for this part?
Send your drawing (STEP, IGES, DWG, DXF or PDF) with quantity and target material to sc@bquq.com or WhatsApp +86 137 1315 7787. Our engineers review the drawing and reply with price, lead time and tooling cost.
What is your MOQ?
We do not set a fixed MOQ. The minimum is decided per part and per process, so tell us your target quantity and we quote against it. Small trial batches are accepted for new parts.
What is the lead time?
Lead time is agreed per order, based on the date you need, the quantity, the material and whether tooling is required. Send your target date with the drawing and we confirm what is achievable before you commit.
What tolerance can you hold?
CNC machining holds ±0.005 mm. Stamping, spring and extrusion parts are made to the tolerances marked on your drawing, and we confirm achievable values at quotation so there are no surprises at inspection.
Can you manufacture parts to my drawing?
Yes. Every order is made to the customer drawing or sample. We run CNC machining, metal stamping, spring coiling and aluminium heat sink extrusion in-house in Dongguan, so one supplier covers the whole part.
STEP, IGES, DWG, DXF and PDF. A 2D drawing with tolerances and surface finish requirements is preferred alongside the 3D model. Hand sketches can be quoted after our engineers redraw them.
How is quality controlled?
Inspection runs through the process, not only at the end: first article approval, in-process checks and a final report per batch, measured with CMM and optical equipment. Material certificates are available on request.
Where is the factory and do you ship worldwide?
Our factory is in Dongguan, Guangdong, China, operating since 2005. We ship worldwide by express, air and sea, and work with the forwarder nominated by the buyer.