Custom CNC Machined Auto Lathe 46 Type Square Bore Quenched Collet
OpeningYour drawing defines the part. We machine it exactly to that spec. Every collet is verified for bore geometry and hardness before shipment. No surprises on your spindle.At a glance: Tolerance ±
Get a Fast Quote for This Part
Send us your drawing / quantity / material — reply within 24h.
Your drawing defines the part. We machine it exactly to that spec. Every collet is verified for bore geometry and hardness before shipment. No surprises on your spindle.
At a glance: Tolerance ±0.005 mm on bore, concentricity ≤0.01 mm TIR, hardness 58–62 HRC, lead time 7–12 days, no MOQ.
This is a 46-type auto lathe collet with a square bore, quenched for wear resistance. It is built for high-cycle production where grip force and repeatability matter. We make it from your print, not from a catalog.
Specifications
Parameter
Value
Material
AISI 4140 or equivalent alloy steel, pre-hardened
Hardness
58–62 HRC, quenched and tempered
Bore shape
Square, per your drawing (sizes from 4 mm to 25 mm)
Outer diameter
46 mm standard, other sizes on request
Concentricity
≤0.01 mm TIR to bore
Tolerance
±0.005 mm on bore width and OD
Surface finish
Ra 0.4 µm on bore, Ra 0.8 µm on OD
Machining process
CNC turning, internal grinding, wire EDM for square bore
Heat treatment
Vacuum quench + temper, scale-free
Inspection
100% dimensional check, hardness test per batch
Batch size
1 piece to 10,000 pieces, no MOQ
Lead time
7 days for prototypes, 12 days for production runs
Country of origin
Made in China, Dongguan factory
We use CNC turning for the OD and face, then internal grinding for the round bore. The square bore is cut with wire EDM after hardening. This avoids distortion and keeps the edges sharp. Each collet is matched to a master gauge before packing.
Three reasons buyers send us their drawings
1. Batch-traceable quality. Every heat number and batch is recorded. If you need to trace a part back to its material lot, we have the paperwork. This is standard for us, not a special request.
2. Inspection report per batch. You get a dimensional report with each shipment. It lists bore width, OD, concentricity, and hardness. No extra charge. You can verify the parts on your bench without waiting for a third-party lab.
3. One factory for CNC, stamping, springs, and heat sinks. Your collet is machined here. But if your assembly also needs a stamped bracket, a compression spring, or an aluminum heat sink, we quote it all in one email. One supplier, one shipping point, one invoice. This cuts your vendor management time in half.
We have run this factory for 20 years. The machines are not new, but they are maintained and calibrated. The operators know how to hold tight tolerances on small parts. This is precision manufacturing, not mass production.
Where these parts are used
A 46-type square bore collet is used in automatic lathes, mainly Swiss-type and sliding headstock machines. The square bore grips square or hex stock without marking the surface. Common applications:
Fastener production: Gripping square stock for hex bolts and nuts.
Electrical connectors: Holding square brass or copper pins during turning.
Hydraulic fittings: Clamping square steel bar for port machining.
Medical device parts: Small square titanium or stainless components for surgical instruments.
Watch and instrument parts: Precision square shafts for clock movements.
In each case, the collet must hold the stock rigidly at high spindle speeds. The quenched surface resists wear from repeated clamping cycles. A soft collet will lose grip after a few thousand cycles. Ours holds tolerance past 100,000 cycles.
The square bore is not a standard off-the-shelf item. It requires wire EDM and careful heat treatment. That is why buyers send us their drawings instead of searching for a stock part.
Q: Is there a minimum order quantity?
A: No. We accept one piece for prototype or replacement use. Production runs are quoted at the same per-piece rate as larger batches, with no setup penalty for small quantities.
Q: How do you guarantee tolerance and quality?
A: We use a coordinate measuring machine (CMM) for bore geometry and a Rockwell hardness tester for every batch. The inspection report is included with shipment. If a part is out of spec, we replace it at no cost.
Q: What is the lead time for a custom collet?
A: Prototype is 7 days from drawing approval. Production runs of 100 pieces or more are 12 days. Heat treatment and wire EDM are the longest steps. We can rush a single piece in 3 days for an extra fee.
Q: Can you provide material certificates?
A: Yes. We supply mill certificates for the raw steel, heat treatment reports, and a certificate of conformity. All are available in English and can be sent with the packing list or by email.
Send your drawing
Send us your PDF or STEP file. We will check the bore geometry, hardness spec, and fit to your spindle. You get a firm quote in 12 hours, including unit price and lead time. No obligation, no design fee.
Email: sc@bquq.com
WhatsApp: +86 13713157787
We are a precision manufacturing supplier in Dongguan, China. Custom CNC collet chuck, made in China, with no MOQ and full traceability. Your drawing is the starting point. Send it today.
Straight answers from the factory, not a sales brochure.
How do I get a quote for this part?
Send your drawing (STEP, IGES, DWG, DXF or PDF) with quantity and target material to sc@bquq.com or WhatsApp +86 137 1315 7787. Our engineers review the drawing and reply with price, lead time and tooling cost.
What is your MOQ?
We do not set a fixed MOQ. The minimum is decided per part and per process, so tell us your target quantity and we quote against it. Small trial batches are accepted for new parts.
What is the lead time?
Lead time is agreed per order, based on the date you need, the quantity, the material and whether tooling is required. Send your target date with the drawing and we confirm what is achievable before you commit.
What tolerance can you hold?
CNC machining holds ±0.005 mm. Stamping, spring and extrusion parts are made to the tolerances marked on your drawing, and we confirm achievable values at quotation so there are no surprises at inspection.
Can you manufacture parts to my drawing?
Yes. Every order is made to the customer drawing or sample. We run CNC machining, metal stamping, spring coiling and aluminium heat sink extrusion in-house in Dongguan, so one supplier covers the whole part.
STEP, IGES, DWG, DXF and PDF. A 2D drawing with tolerances and surface finish requirements is preferred alongside the 3D model. Hand sketches can be quoted after our engineers redraw them.
How is quality controlled?
Inspection runs through the process, not only at the end: first article approval, in-process checks and a final report per batch, measured with CMM and optical equipment. Material certificates are available on request.
Where is the factory and do you ship worldwide?
Our factory is in Dongguan, Guangdong, China, operating since 2005. We ship worldwide by express, air and sea, and work with the forwarder nominated by the buyer.